Blog

Water Heater Repair Boise Blog

Our blog is designed to give homeowners as much information on general plumbing repair tips, not just Boise water heater repair advice.  Many home plumbing maintenance tasks homeowners can be well equipped  to take care of themselves.  Enjoy!

Maintaining a Safe Water Heater

Posted by on Jan 5, 2017 in Gas Water Heater Repair Boise, Water Heater Repair Boise | 0 comments

Statistically, the water heater in ones Boise residence will operate without any major catastrophe; nonetheless, the opportunity it still there which is why one must be aware of the safety info in this article. We want all our customers and readers to be familiar with these hot water heater safety measures so they will have a safe residence.

Significant Reasons Why a Water Heater Will Have a Major Failure

Improper modification of temperature and pressure relief valve settings
Temperature and pressure relief settings are transformed
Unqualified individuals carry out upkeep on the water heater
Absence of regular maintenance by a professional
Inappropriate setup

Ways to Decrease Possible Catastrophic Hot Water Heater Issues

Probably the most vital action a house owner can do to make sure ones water heater is operating safely is to have a professional service it on a regular basis. A plumbing expert will be able to ensure all the safety elements of the water heater are functioning as they should, and to make certain it is operating as energy efficiently as feasible as well.

Water Heater Maintenance Tasks for HomeownersWater Heater T&P Valve

The initial safety upkeep step home owners can do is to check the temperature and pressure relief valve at least annually. It has to open up smoothly and correctly seal itself when it shuts without leaking water once it is shut once more. If it does not open easily, and if it does not seal tightly so water does not leak out, it will need to be replaced. It is a simple and economical replacement process. Nevertheless, one that is essential, for this part sees to it the pressure inside the water heater tank does not boost to the point of exploding.

Some recommend to replace the T&P valve every 3 years, regardless of what its condition, for safety measures.

It is necessary for property owners to be familiar with the temperature level setting of the hot water heater as well. We can not think of any reason that it ought to be set above 120 degrees, or even this will be higher than most individuals will need. Above this temperature, one risks skin burns from the scalding temperature level. If there are youngsters or elderly people in the home, added care should be taken with the highest water temperature.

With hot water heaters many times housed in a garage where things are stored and/or children could play, the temperature setting dial could obtain bumped by mishap and no one is aware of it. If the hot water within the residence seems hotter than typical, examine the temperature level setting immediately. If the setting is bumped too high, it may create an unwanted of pressure inside the water tank too, producing a hazardous circumstance.

Infants and small children may not be able to get away from water that may be too hot, and maintaining a constant thermostat setting can help control the water temperature throughout your home—preventing it from getting too high. (read more)

An additional reason ones water becomes hotter compared to regular, if the temperature level setup has not been altered, is that the thermostat is not working appropriately. It can additionally be the case if the water is chillier than typical too. If when changing the temperature level does not have much of a result, there is possibly glitch with the thermostat and we should look at it.

Other Boise Hot Water Heater Safety Tips Homeowners Need to TakeWater Heater Venting

If one has a gas water heater set up, specific treatment needs to be taken to protect against fires. A fire could start if vapors from combustible products are present. This can conveniently hold true in a garage or basement, with cleaning products, paint, gas containers, or other item which contains combustible vapors. Please ensure these things are not in the same location of the hot water heater.

Being aware of carbon monoxide leaks is very important for homeowners also. It is necessary to have a carbon monoxide gas detector set up in the residence. This harmful gas could get in the residence if a water heater is not appropriately vented to the outside of the home. This is a significant need to have a qualified professional plumbing technician set up ones water heating devices.

Carbon monoxide is odorless, that makes it extremely hard to recognize when it is present in the house. A CO detector will have the ability to alert homeowners of the leak, yet also if any person in the residence is currently having concerns with dizziness, headaches, chest discomforts, throwing up, mental confusion, these are alerting indications of a carbon monoxide leak. If one has any one of these symptoms occurring, leave the residence promptly, go to the hospital, and call a plumbing technician or the gas company to evaluate the home.

If you have any gas-fueled appliances (water heater, furnace, oven, clothes dryer, etc.) in your home, a carbon monoxide detector is imperative. The Consumer Product Safety Commission warns carbon monoxide poisoning kills 200 people each year and causes another 10,000 to need hospital treatment. (read more)

Tankless hot water heaters should also be installed correctly and can trigger carbon monoxide gas leakages too otherwise appropriately vented. It is not simply a standard gas hot water heater concern.

A less harmful, however still messy scenario is when a hot water heater is leaking. A little water, or some condensation can take place around the bottom of the water storage tank sometimes. Nonetheless, if a constant stream of water, even if it is simply a little proceeds, most definitely give us a call. This is an indicator that something is not right with the heater. A majority of water heater failing happen as a result of a leak or some amount. The earlier we can inspect for the issue the more probable it will be for us to fix the water heater, and the less most likely a tiny leak can become a large leak. A large leak could cause an expensive cleaning too. A 30-50 gallon water leak in the house is no little feat to tidy up.

With excellent awareness of how ones hot water heater works, and with exactly what to search for in indications that it is not functioning effectively, Boise homeowners may assist to make sure their residence is safe from a significant plumbing emergency situation.

Using Water Heater Blankets to Save on Heat Loss

Posted by on Nov 1, 2014 in Water Heater Repair Boise | 0 comments

Water heating unit wraps or blankets are probably the most cost effective means of all the energy preservation measures. There are no other conservation measures that has the life expectancy, cost and and payback that the water heating system wraps have suggests Water Heater Repair Boise.

These insulation jackets last as long as the water heating system and if you are as prudent, you can use the old one and put it on the brand-new water heater tank, if it will certainly fit. Typical life of a water heater, 10 years. Expense $30. Money saving varies from $30 to $50 each year, relying on the efficiency of the water heater.Water Heater Repair Boise

What water heater wraps do is preserve the temperature level of the water longer. In other words, the heating elements or gas do not have to come on as often when a insulation jacket is set up. Besides the truth that it saves you money on your energy expenses, it will, without question, prolong the life of the water heating unit. To show this is you and your neighbor work at the same location, 10 miles away. With all else being equal except that you drive to work at 25 mph and he/she does it at 40 mph. He/she gets to work or home in 11 minutes and it takes you 12 minutes. As far as the cars are concerned, which car will use more gas for the exact same range? Which automobile will need more maintenance? Which automobile will last longer?

This puts on a water heater in much the same way. The average home actually only utilizes hot water a little bit more than a hour. As an example, it might take you 45 minutes to clean clothes, however it only takes 2 minutes for the washer to full of hot water. Your kids could take 45 minute showers, they are only utilizing the water in the shower at most 15 minutes. Try staying under a hot shower for more than 15 minutes, you will certainly come out appearing like a trim. What this implies is that for more than 22 hours a day, the water heater just preserves the temperature of the water. So let’s say you are extreme with warm water, let’s double it, it is still more than 20 hours a day simply keeping the temperature level. Plainly the substantial bulk of the cost to operate a water heating system is preserving the temperature of the water when no-one is making use of hot water.

A water heating unit without the insulation jacket comes on to maintain the temperature level typically4 times an hour. One with the insulation jacket 3 times an hour. On top of that the water heating system without the jacket will certainly stay on for a longer duration than one with the jacket. Because all heating elements create hostile environments, regardless if it is electric or gas, the even more times per hour and the longer the heating elements remain on, the shorter the life expectancy of the water heating unit. You will take advantage of the installation of the insulation jacket however who will certainly not benefit are individuals who install them for a living and the producers.  Let us know at Water Heater Repair Boise if you need assistance with sizing or choosing the best one for your home.

Here is another video on how to install a water heater blanket:

Boise Water Heater Maintenance in 10 Minutes

Posted by on Feb 25, 2014 in Water Heater Repair Boise | 0 comments

We are going to put you to work today, however just for about 10 minutes. Yep, that’s all it will consider these two vital water heater upkeep jobs; nevertheless, Water Heater Repair Boise understands they will do an exceptional task of helping with three things:
Having your water heater last as long as possible (that will save you money).
Making sure the water heater runs safely (we do not desire it to explode).
Having it run as energy efficiently as possible (likewise saving you cash).

So with that in mind, are you ready to spend 10 minutes once or two times a year to assist in saving some money? Water Heater Repair Boise ID thought so.

Testing the T&P Relief Valve

Typically called the T&P Valve, or the temperature and pressure relief valve, has a crucial job. It helps make certain excess pressure does not develop inside the water storage tank, or in even more easy terms, it makes sure the water heater does not blow up. As the photo shows, it has a lever or little handle on it. All you have to do is raise it part method then let go of it. Ideally, it snapped back to its closed position quickly. If it is working correctly, a little water can be heard going into the drain pipe below the lever you just lifted and you maybe heard some pressure being released. If none of these things have occurred during the test, the valve will have to be changed.

Carry out a Mimi Water Heater Tank Flush

By nature, rust and rust will occur inside the water tank thanks to the chemical reactions taking place with all the elements inside that are needed to heat the water. We will not get too technical right here, but it is easy to assist avoid this process by doing a flush or draining of all or a portion of the water in the storage tank.

For simply a tiny flush, position a pail under the drain valve below the tank. Open the drain valve and fill up the bucket with water. Drain at least a couple of gallons of water in total. Let the water sit in the container for a couple of minutes to settle and analyze if there is much that settles to the bottom of the bucket. If there is, if the water heater has not been drained for a very long time (or ever), it would be best to do a complete flush of the tank to get as much of the sediment out as possible. You will wish to turn the temperature dial down and may wish to let the water cool off for about an hour initially so it is not too hot while draining it. Also, it would be simpler to connect a hose to the drain valve and let the water go outside rather of utilizing buckets.

If the water looks relatively clean and clear from the mini test you should be all set. When the water heater has an excessive amount of sediment inside of it, it can make loud popping sounds and it lowers its efficiency too.

Though water heaters are fairly upkeep free and easy to operate, any time you feel the smallest bit awkward or are not sure of what to do, it is always best to have a plumbing expert help with the circumstance.

Water Heater Repair Boise

Why is My Boise Water Heater Making Noise

Posted by on Jan 13, 2014 in Water Heater Repair Boise | 0 comments

Water heaters aren’t known to make too much noise when they are running, so it can be worrying when one begins to hear popping, banging or rumbling sounds coming from the unit. Today Water Heater Repair Boise is going to speak about the most usual reason why your water heater could begin making noise and exactly what one can do to quiet it down!

Water Heater Repair Boise

Water heater (Photo credit: km6xo)

The most likely reason your water heater is making sound

The most likely description behind your water heating making banging is that sediment has built up on the bottom of your tank. This sediment is normally comprised of calcium and magnesium deposits from your tap water, and it’s particularly typical in houses that have hard water.

When sediment develops up at the bottom of your water heater’s tank, it traps some hot water under it. As this happens, hot water bubbles start to form and break through the sediment. This frequently results in a “popping” noise that is heard often while your water heater is running.

In addition, the sediment itself might be liable for different water heater noises. That’s due to the fact that the sediment is close to your water heater’s burning elements, which triggers it to burn up and make numerous strange noises. As water flows throughout the water heater, sediment can also break off from the bottom and bang against the sides of the tank.

Ways to stop your water heater from making banging

If your water heater is making sound because of sediment buildup, the first thing one must do is to have it assessed for an apparent cause. Water Heater Repair Boise ID can do this for you and if sediment build-up is the offender, we can flush the water heater tank or recommend another alternative to correct the trouble.

There are also a couple of things you can do to avoid sediment from developing inside the storage tank in the first place. The first is to make certain you have professional upkeep performed on your water heater once each year. Throughout maintenance, we’ll flush your tank and clear away any sediment that has developed since the last maintenance visit.

An additional excellent alternative is to install a water softener in your home. A water softener eliminates minerals from your water prior to they can get into the water heater, which can considerably lower sediment buildup inside the storage tank.

If you have any questions about your water heater making banging give Water Heater Repair Boise us a call today.

Enhanced by Zemanta

8 Water Heater Safety Precautions

Posted by on Dec 3, 2013 in Water Heater Repair Boise | 0 comments

Appropriately preserving ones water heater is important not simply so it works to its complete potential and can conserve some energy money, however for security issues too. Yes, it can blow up – it doesn’t occur too typically for homeowners, but obviously this is something that Water Heater Repair Boise does not desire to have occur to you!

Vents
Venting can be sort of technical but we will go over the fundamentals right here. The vent need to be the exact same diameter as the draft diverter of the water heater tank. It is expected to increase and out (for atmospherically vented heaters). Not other directs like up, down, up and out. For direct-vent water heaters, the vent need to go out a side wall. As for power-vent heaters, the fan blows the fumes out, so there is some versatility in the instructions they are vented.

Any roof or wall that the vent goes through need to be a double wall. The single wall pass throughs ought to be screwed with three screws per area. If these fundamentals are not adhered to, the vents can fall apart over time and carbon monoxide gas can cause significant problems within ones home. Of course we do not desire that to happen!

The only other interested in ventilation is that of backdrafting. The fumes can eat the vents with acid condensation. If plenty of this gets on cold piping and the water heater it will not be a great scenario for a correctly working water heater. If the fumes return inside the rather of being appropriately vented outside, the fumes can enter the living areas of the home. Soot issues can occur too.

Dielectric Connectors
The steel water heater is linked to cooper pipes by the dielectric connectors. When two these two metals are assembled in water electrolysis occurs. The process rusts one metal away to protect the other. This procedure is essential in safeguarding the inside of the water heater. Evaluation for leakages must be done where the connections are made.

Temperature and Pressure Relief Valve
This is kinda of a fundamental part of the water heater, for it helps make certain the darn thing does not blow up under pressure if the temperature level surpasses the correct limitations the water heater is designed for. Once a year (a minimum of) the T&P valve should be examined to see to it, it is working effectively, for they can be vulnerable to failure. Just lifting up on the handle water needs to stream freely out and stop when the handle is let go of. If it just runs or trickles, or does nothing at all, it will need to be changed.

The drain lines for the T&P line must not be routed up, because water doesn’t flow uphill too well. Make certain it goes down and or out please. If water is running out the drain line frequently, it is the sign of something incorrect too. It can be among numerous various things that we will not enter right here – simply get in touch with a regional plumbing professional please.

Earthquake Straps
Yep, even if you don’t live in an earthquake area and are required to have these on ones water heater, it is a good idea to do so. It looks like most all brand-new homes in sub-divisions nowadays have the water heater in the garage. Yes, there is typically a concrete curb in front of it so one does not drive an automobile into it, but things can inadvertently knock it over so be safe and strap that say thanks to in.

Temperature Level Setting
It seems most domestic water heater tanks have settings of warm – hot – really hot … and not degree settings. Some “suggestions” on saving energy in the house especially in the winter time, say to decrease the setting on the tank to 120 degrees. That’s terrific for conserving energy however legionella microorganisms, which triggers Legionnaire’s disease can grow at 120 degrees. By inhaling the mist from the water in the shower, one can inhale the microorganisms. Try to discover a medium between 130 and 120 degrees. Above 130 degrees is technically a scalding temperature so beware.

Anode Rods
These normally are made from aluminum and there is absolutely nothing wrong with that in concept, though we suggest utilizing magnesium ones. Let’s say for whatever reason there is some kind of emergency or catastrophe where one lives and one needed to make use of the water in the water heater for drinking water (because great deals of emergency preparedness individuals advise doing so). The water that comes out of the drain valve is the water at the bottom of the tank. If one has aluminum anodes, that water will be loaded with aluminum compounds, which is not good for the body. It is bad for the stomach, intestinal tract and joints.

The anodes aid with rust protection and are important in extending the life of the water heater. They can likewise assist with smell issues with the water. Generally, magnesium anodes simply work much better for lots of different reasons like the health advantages, let build up of sediment, a quieter water heater, and they have the tendency to work much better with softened water.

Drain Valve
Ok, simply examine it a minimum of yearly to make sure the darn thing opens and works. And it is good to drain and flush the tank at least once a year anyhow (something you of course are doing already). If for some reason one has to utilize the water throughout a catastrophe or drain it to quite a noisy tank and have not drained it frequently, and it doesn’t open, it will take longer to correct the trouble you are initially trying to repair.

Combustion Changer Hatch
Because gas and oil water heaters breathe the air drawn in from beneath, combust with it and exhale it, it is very important to keep the area around it, specifically beneath the water heater, clean and swept. If if is not burning correctly, it can cause composing problems (mentioned above), along with combustion and fume issues and potentially be a fire danger. Some of analyzing the chamber and exactly how the flame burns is objective so we are not going to enter a bunch of detail here. it is crucial to see if the combustion chamber roof has a lot of rust or water markings or is black in color. These are not a great indication at all. One must see some blue flame at the bottom when it burns and orange and yellow at the top, nonetheless, the yellow should not be very high up. One should see gray metal, some white condensation marks are ok.

Water Heater Repair Boise has put together an infographic to highlight the information above:

Water Heater Repair Boise

Enhanced by Zemanta